Ilmoita minulle, kun tuotetta on jälleen tarjolla varastossa
Email:
Varastovahti on luotu. Lähetämme sähköpostin kun tuotetta on taas varastossa.
Tämä toiminto vaatii sisäänkirjautumisen. Luo käyttäjä ja voit käyttää listojamme esim. säännöllisiä ostoksia ja toivelistoja varten Luo käyttäjä Kirjaudu
Adjustable Holder. Fits devices with slim skin. For use with Apple original Lightning to USB Cable.\n\nThis holder for cable attachment can, combined with an Apple cable, be used for charging your iPhone. First you mount the cable into place onto the holder, then it connects automatically to your iPhone every time you place the device in the holder.\n\nNote! Cable not included.\nThe cable attachment holder can be combined with Apple original Lightning to USB Cable (Apple article. no. MD818ZM/A. You can charge you iPhone by connecting it to the car’s USB socket, or use it with a USB/cig-plug adapter for the car’s 12V socket.\n\nTo use the holder, you first set the width to fit for your skin, then you can easily place your iPhone in the holder. Fits devices with slim sized skins.\n\nThe holder is made of black ABS plastic. It is easy to put the device into the holder, and just as easy to take it with you when leaving the vehicle. The holder is equipped with a tilt swivel so you can adjust the angle of your device in order to avoid light reflection on the screen. Attach onto ProClip Mounting Platform.\n\nINSTALLATION INSTRUCTIONS:\n1. To adjust the holder for your device: Loosen the screws on the front side of the holder, so the sides of the holders can be adjusted. Place the device in the holder and press the sides together so the device is firmly in place. Tighten the screws on the front side of the holder.\n\n2. Place the connector of the cable in the hole in the lower part of the holder. Carefully press the connector downward and forward so it passes the locking and goes into the hole. Press until you hear/feel the connector snap into place in the holder.\n\n3. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted.\n\n4. The holder is in place.
Tuotekuvaus
Brodit Holder for Cable Attachment - autopidike tuotteelle matkapuhelin
Tuotteen tyyppi
Autopidike
Käyttötarkoitus:
Matkapuhelin
Sopii asennukseen
Auto
Tuotemateriaali
ABS-muovi
Väri
Musta
Generelt
Tuotteen tyyppi
Telefonlinje - RJ-11 Kabel-tv
Tuotemateriaali
DirectSound3D GX 1.0, Dolby Home Theater v4
Väri
2 x minne - SO DIMM 72-pin
Löydämme tuotteen järjestelmästämme helposti seuraavalla tuotenumerolla
SKU:
BRO-514667
EAN:
7320285146679
Varför upplever jag att exakt samma varor finns med flera olika produktnummer?
Tillverkarna ger ofta ut samma produkter med olika produktnummer, vanligtvis handlar det uteslutet om olika versioner av emballage. T.ex. så kan emballaget målinriktas för olika länder.
Vi försöker på bästa sätt samla varorna, men det kan upplevas som att samma produkter finns med olika produktnummer i vårt system.